light bronze

Showing 1–16 of 22 results

4″ x .024 Aluminum Corrugated Round Downspout, Select Colors

We recommend corrugated downspout for areas of the country that experience snow and ice. Corrugation allows for expansion in the event of ice build-up in the downspout, and also helps hide nicks and dents from daily exposure.

Note: Select Color corrugated aluminum downspout, shown here in Grecian Green, is priced the same per 10-foot length as our Standard Colors (see Aluminum Color Chart below).

Due to the machine setup required to produce Select Color Corrugated Downspout and Elbows, there is a $100.00 up charge (one up charge per color, per order).

Downspout sections are available in 10′ pre-cut lengths. Each box holds 60 ft. of 4″ downspout. Don’t forget to order additional downspout for elbow offsets and future repairs.

You will need to reduce the size of the opening on the elbows and downspout.

Downspout orders LONGER than 6′ will be shipped via truck and subject to a MINIMUM shipping fee of $150.00

One to three pieces of downspout can be sent UPS. The 10′ downspout will be cut into 6′ & 4′ sections. UPS charges will run in the $100 range. Please indicate in the “Order Notes” area at checkout whether you want a UPS or freight quote.

To order Corrugated Select Color Downspout, please call us at 269.665.2700.

Straps for 3″ & 4″ Downspout, Aluminum

$1.50$1.80

These aluminum straps measure 15″ x 2.25″ x .032″. They will fit both 3″ and 4″ downspout.

We recommend two straps for one-story and three straps for a two-story installation. They can be screwed to the house, wrapped around the downspout and screwed in the front.

Another method is to wrap the strap over the front of the downspout and screw on both sides.

A rosette or fleur-delis can be used in either situation.

8″ x .032 Half Round Aluminum Gutter

$4.35$5.25

Gutter can be shipped in lengths of 6, 10, 15 and 19 feet.  Gutter can also be shipped at  20 & 26 foot lengths, but is considered and rated as excessive length by freight companies. (6′ maximum lengths shipped via UPS)

Our unique front lip design adds 3 times the front-to-back strength compared to traditional front roll out gutters.

Available in several colors, featuring a low gloss baked-on enamel finish which can be painted. See Color Chart below.

We also offer KYNAR Standard Color .032 Aluminum Gutter, by special order only. The combined quantity of gutter and downspout must equal at least 500 lineal feet. Call for color chart. Approximate lead time 4 weeks.

Gutter will be shipped in our custom corrugated Gutter Box, which is extremely durable to withstand the possibilities of shipping damage. We can nest 4-6 pieces of gutter per box depending on the size of gutter and shipping destination. Gutter Box is $2.50 per foot, and we will add the cost to your order.

Price shown is per foot, please enter the total number of feet needed in the Quantity box. IMPORTANT: When you’re checking out, you’ll have the opportunity to specify the quantity of each length of gutter you need. You’ll enter this info in the “Order Notes & Item Length Specs” box at checkout.

Gutter orders LONGER than 6′ will be shipped via truck and subject to a MINIMUM shipping fee of $150.00

One to five pieces of gutter can be sent UPS in 6′ sections. UPS charges will run in the $100 range. Please indicate in the “Order Notes” area at checkout whether you want a UPS or freight quote.

Each gutter and downspout order is unique at Classic Gutter Systems. Once you’ve placed your order on this website, you’ll be contacted within 48 hours with a complete, detailed quote including packaging and shipping costs.

5″ Stamped Fascia Brackets

$3.50$3.75

We recommend spacing our fascia brackets every 32″ on center. Our stamped fascia bracket requires the fascia board to be at least 4½” in height.

The gutter is secured by folding the back tab down and the front tab over the lip of the gutter. Stamped fascia brackets are installed on a fascia board using 3 – #12 1 7/8” hex head stainless steel screws.

Stamped fascia brackets are not as strong as our cast fascia brackets. If you are in an area that has heavy snow fall, we recommend cast fascia brackets for strength.

Copper and chromated aluminum (needs to be painted) available in 5″, 6″ and 8″ sizes.
Galvalume is available in 5″ and 6″ sizes.

3″, 4″ & 5″ Round Flat Bottom Outlets, Copper & Aluminum

$3.00$17.00

These flat bottom round outlets are available in 3″, 4″ & 5″ sizes in copper and aluminum (colors are almond, black, clay, light bronze, low gloss white, musket brown, painted galvalume, royal brown and wicker). Some colors may take extra lead time to ship. See color chart below.

(Note: When ordering copper outlets, be sure to choose copper as the Color in the dropdown menu below.)

3″ x .019 Aluminum Corrugated Round Downspout, Select Colors

We recommend corrugated downspout for areas of the country that experience snow and ice. Corrugation allows for expansion in the event of ice build-up in the downspout, and also helps hide nicks and dents from daily exposure.

Note: Select Color corrugated aluminum downspout, shown here in Grecian Green, is priced the same per 10-foot length as our Standard Colors (see Aluminum Color Chart below).

Due to the machine setup required to produce Select Color Corrugated Downspout and Elbows, there is a $100.00 up charge (one up charge per color, per order).

Downspout sections are available in 10′ pre-cut lengths. Each box holds 80 ft. of 3″ downspout. Don’t forget to order additional downspout for elbow offsets and future repairs.

Downspout orders LONGER than 6′ will be shipped via truck and subject to a MINIMUM shipping fee of $150.00

One to three pieces of downspout can be sent UPS. The 10′ downspout will be cut into 6′ & 4′ sections. UPS charges will run in the $100 range. Please indicate in the “Order Notes” area at checkout whether you want a UPS or freight quote.

To order Corrugated Select Color Downspout, please call us at 269.665.2700.

Interior/Exterior Outlets, Aluminum

$4.00$11.00

Can be mounted as an interior or exterior outlet; attached to the gutter with 3/8″ stainless steel screws and sealant.

See our Color Chart below.

We do not precut holes in the gutter for the outlet, however this can easily be accomplished using the same size hole saw as the outlet size.

3″ x .019 Aluminum Smooth Round & Corrugated Downspout

$16.50$19.80

Downspout sections are available in 10′ pre-cut lengths. We recommend corrugated downspout for areas of the country that experience snow and ice. Corrugation allows for expansion in the event of ice build-up in the downspout. Corrugation also helps hide nicks and dents from daily exposure.

Smooth downspout is recommended mainly for southern climates. We take great care in the packaging of our downspout; however, flawless sections of smooth downspout cannot be guaranteed due to potential improper handling by the freight carriers.

All of our 3″ aluminum smooth downspout has one expanded end, allowing for a a far superior installation to the traditional crimped joint. We are proud to be the only manufacturer to supply 13 colors of 3″ aluminum downspout with an expanded end.

Price shown is per 10 foot length. Each box holds 80 ft. of 3″ downspout.

Our Aluminum Downspout is available in Smooth and Corrugated styles in these four Standard Colors: high gloss white, low gloss white, dark bronze and royal brown (see Aluminum Color Chart below). Note: We can make Select Color Corrugated Downspout and Elbows for a $100.00 up charge (one charge per color, per order).

Don’t forget to order additional downspout for elbow offsets and future repairs.

Downspout orders LONGER than 6′ will be shipped via truck and subject to a MINIMUM shipping fee of $150.00

One to three pieces of downspout can be sent UPS. The 10′ downspout will be cut into 6′ & 4′ sections. UPS charges will run in the $100 range. Please indicate in the “Order Notes” area at checkout whether you want a UPS or freight quote.

Each gutter and downspout order is unique at Classic Gutter Systems. Once you’ve placed your order on this website, you’ll be contacted within 48 hours with a complete, detailed quote including packaging and shipping costs.

8″ Aluminum Strip Miters For Half Round Gutter

$6.00$7.20

We manufacture strip miters which duplicate the configuration of a corner. Strip miters are installed on the outside of the gutter and are approximately 3″ wide.

Installation:
90° corner-cut each gutter length at 45° angles
45° corner-cut each gutter length at 22½° angles

Your cuts do not need to be perfect, the strip miter allows for tolerance while maintaining a custom corner. An additional 12″ needs to be added to each piece of gutter used on an outside mitered corner. Inside miters do not require extra gutter. The miters are installed with 3/8″ stainless steel screws and sealed on the inside with sealant.

See Aluminum Color Chart below.

6″ Aluminum Flat End Caps

$3.00$3.60

Six inch end caps are full coverage and non reversible. Be sure to order both left and right end caps as needed.

End caps are attached by crimping the edges and finishing with sealant.

See Aluminum Color Chart and our End Cap Crimper below.

For a custom, finished touch, add our Decorative End Cap Insert.

6″ Aluminum Strip Miters For Half Round Gutter

$5.50$6.60

We manufacture strip miters which duplicate the configuration of a corner. Strip miters are installed on the outside of the gutter and are approximately 3″ wide.

Installation:
90° corner-cut each gutter length at 45° angles
45° corner-cut each gutter length at 22½° angles

Your cuts do not need to be perfect, the strip miter allows for tolerance while maintaining a custom corner. An additional 12″ needs to be added to each piece of gutter used on an outside mitered corner. Inside miters do not require extra gutter. The miters are installed with 3/8″ stainless steel screws and sealed on the inside with sealant.

See Aluminum Color Chart below.

Straps for 5″ Downspout, Aluminum

$2.00

These aluminum straps measure 21″ x 2.25″ x .032″. They fit 5″ downspout.

We recommend two straps for one-story and three straps for a two-story installation. They can be screwed to the house, wrapped around the downspout and screwed in the front.

Another method is to wrap the strap over the front of the downspout and screw on both sides.

A rosette or fleur-delis can be used in either situation.

5″ Aluminum Strip Miters For Half Round Gutter

$5.00$6.00

We manufacture strip miters which duplicate the configuration of a corner. Strip miters are installed on the outside of the gutter and are approximately 3″ wide.

Installation:
90° corner-cut each gutter length at 45° angles
45° corner-cut each gutter length at 22½° angles

Your cuts do not need to be perfect, the strip miter allows for tolerance while maintaining a custom corner. An additional 12″ needs to be added to each piece of gutter used on an outside mitered corner. Inside miters do not require extra gutter. The miters are installed with 3/8″ stainless steel screws and sealed on the inside with sealant.

See Aluminum Color Chart below.

6″ x .032 Half Round Aluminum Gutter

$2.75$3.30

Gutter can be shipped in lengths of 6, 10, 15 and 19 feet.  Gutter can also be shipped at  20 & 26 foot lengths, but is considered and rated as excessive length by freight companies. (6′ maximum lengths shipped via UPS)

Our unique front lip design adds 3 times the front-to-back strength compared to traditional front roll out gutters.

Available in several colors, featuring a low gloss baked-on enamel finish which can be painted. See Color Chart below.

We also offer KYNAR Standard Color .032 Aluminum Gutter. Special order only. The combined quantity of gutter and downspout must equal at least 500 lineal feet. Call for color chart. Approximate lead time 4 weeks.

Gutter will be shipped in our custom corrugated Gutter Box, which is extremely durable to withstand the possibilities of shipping damage. We can nest 4-6 pieces of gutter per box depending on the size of gutter and shipping destination. Gutter Box is $2.50 per foot, and we will add the cost to your order.

Price shown is per foot, please enter the total number of feet needed in the Quantity box. IMPORTANT: When you’re checking out, you’ll have the opportunity to specify the quantity of each length of gutter you need. You’ll enter this info in the “Order Notes & Item Length Specs” box at checkout.

Gutter orders LONGER than 6′ will be shipped via truck and subject to a MINIMUM shipping fee of $150.00

One to five pieces of gutter can be sent UPS in 6′ sections. UPS charges will run in the $100 range. Please indicate in the “Order Notes” area at checkout whether you want a UPS or freight quote.

Each gutter and downspout order is unique at Classic Gutter Systems. Once you’ve placed your order on this website, you’ll be contacted within 48 hours with a complete, detailed quote including packaging and shipping costs.

 

4″ x .024 Aluminum Smooth Round & Corrugated Elbows

$3.75$4.50

Smooth elbows will have one end expanded for ease of installation. 

Our Aluminum Elbows are available in several Standard Colors (smooth and corrugated styles) and Select Colors in smooth style. See Color Chart below. We can also produce Select Color corrugated elbows for a $100.00 up charge per order.

The average installation requires two elbows at the top and one at the bottom. If you are connecting your downspout into a drain tile, the elbow at the bottom is not necessary.

The offset is the measurement of two connected elbows. 40 degree elbows have a 3″–9″ offset; 72 degree elbows have a 9″ offset.

The degree of elbow you use is determined by the overhang of your structure. To determine the overhang, measure the distance between the wall of your building and the back of the outlet. An overhang of 9″ will require 2- 72 degree elbows. If your overhang is greater than 9″ you’ll need to insert a piece of downspout between the elbows.

An overhang of less than 9″ will require (2) 40 degree elbows. This elbow combination also works when making a transition around a ledge or other protrusions.

You’ll need to reduce the size of the opening on the elbows and downspout when using either corrugated or smooth options. (see Product Description below left and our Elbow & Downspout Crimper Tool.)

Note: Smooth elbows will have folds in the bend.