6"

Showing 1–16 of 46 results

Classic Bar Brackets

$5.50$11.25

Our Classic Bar Bracket is available in copper and chromated aluminum. Chromating is an industrial primer for aluminum and needs to be painted.

We recommend spacing our fascia brackets every 32″ on center. The bracket can be mounted to either the fascia board or rafter tails.

For use with an angled fascia: In areas without snow or ice, the back of the bracket can be bent in a vice to the desired angle of the fascia or rafter tail.

The fascia bracket is installed with 3 – #10 1½” hex head stainless steel screws. The gutter nests inside the bracket and is anchored by folding down both tabs.

The Classic Bar Bracket requires the fascia board to be a minimum of 3½” in height.

Scroll Bar Brackets

$7.00$18.00

Our Scroll Bar Bracket is available in copper and chromated aluminum. Chromating is an industrial primer for aluminum and needs to be painted.

We recommend spacing our fascia brackets every 32″ on center. The bracket can be mounted to either the fascia board or rafter tails.

For use with an angled fascia: In areas without snow or ice, the back of the bracket can be bent in a vice to the desired angle of the fascia or rafter tail.

The fascia bracket is installed with 3 – #10 1½” hex head stainless steel screws. The gutter nests inside the bracket and is anchored by folding down both tabs.

The Scroll Bar Bracket requires the fascia board to be a minimum of 3½” in height.

Roof Mount Classic Bar Brackets

$7.50$16.00

Our Roof Mount Classic Bar and Scroll Bar Brackets are available in copper and chromated aluminum. Chromating is an industrial primer for aluminum and needs to be painted.

We recommend spacing our fascia brackets every 32″ on center. The bracket can be mounted to either the fascia board or rafter tails.  This bracket is not intended to be installed in areas with heavy snow or ice.

For a roof mount installation, the back of the bracket can be bent in a vice to the desired angle roof.

The fascia bracket is installed with 2 – #10 1½” hex head stainless steel screws. The gutter nests inside the bracket and is anchored by folding down both tabs.

Hidden Half Round Gutter Brackets with Rods

$1.50$9.25

Our 5″, 6″ and 8″ gutter brackets are available in two materials. The .063 aluminum brackets are compatible with aluminum and Galvalume gutter system. Our .060 stainless steel brackets are compatible with copper, aluminum and Galvalume gutter system.

They can be installed by two different methods. Whichever you choose, we recommend a general spacing of the brackets every 32″ on center. Extra strength can be achieved by placing the brackets closer together. This is a good idea for sections of the country dealing with heavy snow loads. Areas not dealing with heavy ice or snow can space the brackets further apart.

Gutter Brackets hung from the roof with a rod are called hanger units. Existing roofs, with a standard shingle installation, will have the rod placed over the first course of shingles and the flat part of the rod secured with 1½” screws under the second row of shingles. A new roof installation allows the rods to be placed under the roofing material, especially important for tile or slate roofs.

Stainless steel rods are shipped straight and need to be bent on-site. A rod bending tool can be rented to consistently bend the stainless steel rods to the same angle. The rod bender deposit is refundable upon the return of the tool. The bracket tab can be bent over the back hem of the gutter for a free floating installation.

For coastal locations we recommend using our marine stainless steel rods.

The aluminum rods are also shipped straight and can be bent by hand.

Hanger units are shipped with 1½” stainless steel screws and include the 2 stainless steel nuts used with the rods.

6″ Splash Fascia Bracket for KWM

$11.00$21.00

Our KWM compatible cast brackets consist of a select group of Classic Gutter Systems, LLC top-selling brackets. The back hook of these brackets have been modified to fit gutter produced from a 6″ KWM gutter machine.

Please note that any of our cast brackets can be made as a KWM compatible bracket with enough lead time. A minimum order may be required.

Fascia brackets are available in solid brass or chromated aluminum. Our cast brass items are 88% copper, medium in color and will oxidize over time. Chromating is an industrial primer for aluminum castings and needs to be painted.

We recommend spacing our fascia brackets every 32″ on center. Fascia brackets can be mounted the fascia board with three 1-1/2″ stainless steel hex head screws.

For an angled fascia application we offer 7.5, 15, 22.5, 30, 37.5 and 45 degree wedges to be used with our fascia brackets. In a situation where a fascia installation is not applicable, a fascia bracket and a roof bar can be used. See Additional Information below for wedge selection.

6″ Streamline Fascia Bracket for KWM

$8.00$14.25

Our KWM compatible cast brackets consist of a select group of Classic Gutter Systems, LLC top-selling brackets. The back hook of these brackets have been modified to fit gutter produced from a 6″ KWM gutter machine.

Please note that any of our cast brackets can be made as a KWM compatible bracket with enough lead time. A minimum order may be required.

Fascia brackets are available in solid brass or chromated aluminum. Our cast brass items are 88% copper, medium in color and will oxidize over time. Chromating is an industrial primer for aluminum castings and needs to be painted.

We recommend spacing our fascia brackets every 32″ on center. Fascia brackets can be mounted the fascia board with three 1-1/2″ stainless steel hex head screws.

For an angled fascia application we offer 7.5, 15, 22.5, 30, 37.5 and 45 degree wedges to be used with our fascia brackets. In a situation where a fascia installation is not applicable, a fascia bracket and a roof bar can be used. See Additional Information below for wedge selection.

K-Style Hidden Gutter Brackets

$1.50$3.50

Our 5″ and 6″ K-Style gutter brackets are available in two materials. The .063 aluminum brackets are compatible with aluminum and Galvalume gutter system. Our .060 stainless steel brackets are compatible with copper, aluminum and Galvalume gutter system.

We recommend a general spacing of the brackets every 32″ on center. Extra strength can be achieved by placing the brackets closer together. This is a good idea for sections of the country dealing with heavy snow loads. Areas not dealing with heavy ice or snow can space the brackets further apart.

 

Copper Strip Miters For K-Style Gutter

$13.00$18.00

We manufacture strip miters which duplicate the configuration of a corner. Strip miters are installed on the outside of the gutter and are approximately 3″ wide.

Installation:
90° corner-cut each gutter length at 45° angles
45° corner-cut each gutter length at 22½° angles

Your cuts do not need to be perfect, the strip miter allows for tolerance while maintaining a custom corner. An additional 12″ needs to be added to each piece of gutter used on an outside mitered corner. Inside miters do not require extra gutter. The miters are installed with 3/8″ stainless steel screws and soldered on the inside.

K-Style Radius Gutter, .034 Copper

$575.00

Our .034 Copper K-Style Radius Gutter is available in 5″ and 6″ sizes; 90″ sections only.

2-3 weeks lead time.

One radius angle per template (each change in angle will require a separate template). Radius gutter sections will be manufactured only from Classic Gutter Systems template kit, which will be sent, no charge, upon completion of an estimate.

Protective Crate (necessary for shipping) is $65.00, and up to 5 pieces of radius gutter can be nested in one crate.

Need an estimate? Download our Radius Gutter Estimate Form here.

K-Style Radius Gutter, .050 Aluminum

$475.00

Our .050 Mill Finish Aluminum K-Style Radius Gutter is available in 5″ and 6″ sizes; 90″ sections only.

2-3 weeks lead time.

One radius angle per template (each change in angle will require a separate template). Radius gutter sections will be manufactured only from Classic Gutter Systems template kit, which will be sent, no charge, upon completion of an estimate.

Protective Crate (necessary for shipping) is $65.00, and up to 5 pieces of radius gutter can be nested in one crate.

Need an estimate? Download, complete and submit our Radius Gutter Estimate Form here.

K-Style Radius Gutter, 26 Gauge Galvalume

$475.00

Our 26 gauge Galvalume K-Style Radius Gutter is available in 5″ and 6″ sizes; 90″ sections only.

2-3 weeks lead time.

One radius angle per template (each change in angle will require a separate template). Radius gutter sections will be manufactured only from Classic Gutter Systems template kit, which will be sent, no charge, upon completion of an estimate.

Protective Crate (necessary for shipping) is $65.00, and up to 5 pieces of radius gutter can be nested in one crate.

Need an estimate? Download our Radius Gutter Estimate Form here.

Gutter Hood, 26 Gauge Galvalume

$1.95$2.95

Gutter hood is designed to be used with a fascia bracket installation. Gutter hood is available in 6′ sections shipped via UPS or 10′ maximum lengths shipped via common carrier.

Clips inserted on the front lip of the gutter hold the gutter hood in place. The back of the gutter hood can be made flat to be placed under the shingles or bent (as shown in the photo) for a fascia attachment.

We highly recommend ordering our gutter when using gutter hood. We suggest that you order a sample of a gutter hood to confirm compatability, if not using our gutter.

NOTE: Gutter hood cannot be installed with a fascia angle greater than approximately 20 degrees.

All clips and screws necessary for installation are included.

Price shown is per foot.

Gutter Hood, .032 Aluminum Colors

$1.95$2.95

Gutter hood is designed to be used with a fascia bracket installation. Gutter hood is available in 6′ sections shipped via UPS or 10′ maximum lengths shipped via common carrier.

Clips inserted on the front lip of the gutter hold the gutter hood in place. The back of the gutter hood can be made flat to be placed under the shingles or bent (as shown in the photo) for a fascia attachment.

We highly recommend ordering our gutter when using gutter hood. We suggest that you order a sample of a gutter hood to confirm compatability, if not using our gutter.

NOTE: Gutter hood cannot be installed with a fascia angle greater than approximately 20 degrees.

All clips and screws necessary for installation are included.

See Aluminum Color Chart below, and specify the color needed in the “Order Notes” box at checkout.

Price shown is per foot.

Galvalume Strip Miters For Half Round Gutter

$5.00$8.00

We manufacture strip miters which duplicate the configuration of a corner. Strip miters are installed on the outside of the gutter and are approximately 3″ wide.

Installation:
90° corner-cut each gutter length at 45° angles
45° corner-cut each gutter length at 22½° angles

Your cuts do not need to be perfect, the strip miter allows for tolerance while maintaining a custom corner. An additional 12″ needs to be added to each piece of gutter used on an outside mitered corner. Inside miters do not require extra gutter. The miters are installed with 3/8″ stainless steel screws and soldered or sealed with sealant.

We do not sell box miters. We believe the use of a strip miter eliminates extra seams while maintaining the strength of your corner.

Half Round Radius Gutter, .050 Mill Finish Aluminum

$475.00$525.00

Our Radius Gutter is available in 5″, 6″, 8″ half round or K-style; 90″ sections only.

2-3 weeks lead time.

One radius angle per template (each change in angle will require a separate template). Radius gutter sections will be manufactured only from Classic Gutter Systems template kit, which will be sent, no charge, upon completion of an estimate.

Protective Crate (necessary for shipping) is $65.00, and up to 5 pieces of radius gutter can be nested in one crate.

Need an estimate? Download our Radius Gutter Estimate Form here.

Half Round Radius Gutter, 26 Gauge Galvalume

$475.00$525.00

Our Galvalume Radius Gutter is available in 5″, 6″, 8″ half round or K-style; 90″ sections only.

2-3 weeks lead time.

One radius angle per template (each change in angle will require a separate template). Radius gutter sections will be manufactured only from Classic Gutter Systems template kit, which will be sent, no charge, upon completion of an estimate.

Protective Crate (necessary for shipping) is $65.00, and up to 5 pieces of radius gutter can be nested in one crate.

Need an estimate? Download our Radius Gutter Estimate Form here.