5"

Showing 1–16 of 39 results

Classic Bar Brackets

$5.50$11.25

Our Classic Bar Bracket is available in copper and chromated aluminum. Chromating is an industrial primer for aluminum and needs to be painted.

We recommend spacing our fascia brackets every 32″ on center. The bracket can be mounted to either the fascia board or rafter tails.

For use with an angled fascia: In areas without snow or ice, the back of the bracket can be bent in a vice to the desired angle of the fascia or rafter tail.

The fascia bracket is installed with 3 – #10 1½” hex head stainless steel screws. The gutter nests inside the bracket and is anchored by folding down both tabs.

The Classic Bar Bracket requires the fascia board to be a minimum of 3½” in height.

Scroll Bar Brackets

$7.00$18.00

Our Scroll Bar Bracket is available in copper and chromated aluminum. Chromating is an industrial primer for aluminum and needs to be painted.

We recommend spacing our fascia brackets every 32″ on center. The bracket can be mounted to either the fascia board or rafter tails.

For use with an angled fascia: In areas without snow or ice, the back of the bracket can be bent in a vice to the desired angle of the fascia or rafter tail.

The fascia bracket is installed with 3 – #10 1½” hex head stainless steel screws. The gutter nests inside the bracket and is anchored by folding down both tabs.

The Scroll Bar Bracket requires the fascia board to be a minimum of 3½” in height.

Roof Mount Scroll Bar Brackets

$9.50$18.50

Our Roof Mount Classic Bar and Scroll Bar Brackets are available in copper and chromated aluminum. Chromating is an industrial primer for aluminum and needs to be painted.

We recommend spacing our fascia brackets every 32″ on center. The bracket can be mounted to either the fascia board or rafter tails.  This bracket is not intended to be installed in areas with heavy snow or ice.

For a roof mount installation, the back of the bracket can be bent in a vice to the desired angle roof.

The fascia bracket is installed with 2 – #10 1½” hex head stainless steel screws. The gutter nests inside the bracket and is anchored by folding down both tabs.

Copper Strip Miters For K-Style Gutter

$13.00$18.00

We manufacture strip miters which duplicate the configuration of a corner. Strip miters are installed on the outside of the gutter and are approximately 3″ wide.

Installation:
90° corner-cut each gutter length at 45° angles
45° corner-cut each gutter length at 22½° angles

Your cuts do not need to be perfect, the strip miter allows for tolerance while maintaining a custom corner. An additional 12″ needs to be added to each piece of gutter used on an outside mitered corner. Inside miters do not require extra gutter. The miters are installed with 3/8″ stainless steel screws and soldered on the inside.

Copper Traditional Leader Heads

$140.00$195.00

Leader heads are placed at the top of the downspout and will accommodate 1-2 elbows.

Traditional copper leader heads are available in 3″, 4″ and 5″ sizes.

One of the photos shows an optional Fleur-de-Lis Cut-Off installed. You may also use our Gutter Trim as an accent.

Aluminum Roof Vent Pipe

$80.00$95.00

Be a talk of the neighborhood and improve the appearance of the exposed PVC piping on your roof with our distinctive pipe vent cover.

Material is chromated aluminum (needs to be painted); also available in copper.

The Roof Vent Pipe has an adjustable lead sleeve that allows for the installation on a roof pitch between 2/12 and 10/12.

4″ Vent Pipe:
Height 14″
Plate 15¼ x 12⅜”
Pipe Diameter 3⅞”
To be used to cover 3″ PVC pipe

5″ Vent Pipe:
Height 14″
Plate 15½ x 15″
Pipe Diameter 4¾”
To be used to cover 4″ PVC pipe

Copper Roof Vent Pipe

$125.00

Be a talk of the neighborhood and improve the appearance of the exposed PVC piping on your roof with our distinctive copper roof vent cover. (4″ vent pipe may be different than photo – may not include cap.)

Also available in chromated aluminum (needs to be painted).

The Roof Vent Pipe has an adjustable lead sleeve that allows for the installation on a roof pitch between 2/12 and 10/12.

4″ Vent Pipe:
Height 14″
Plate 15¼ x 12⅜”
Pipe Diameter 3⅞”
To be used to cover 3″ PVC pipe

5″ Vent Pipe:
Height 14″
Plate 15½ x 15″
Pipe Diameter 4¾”
To be used to cover 4″ PVC pipe

K-Style Radius Gutter, .034 Copper

$575.00

Our .034 Copper K-Style Radius Gutter is available in 5″ and 6″ sizes; 90″ sections only.

2-3 weeks lead time.

One radius angle per template (each change in angle will require a separate template). Radius gutter sections will be manufactured only from Classic Gutter Systems template kit, which will be sent, no charge, upon completion of an estimate.

Protective Crate (necessary for shipping) is $65.00, and up to 5 pieces of radius gutter can be nested in one crate.

Need an estimate? Download our Radius Gutter Estimate Form here.

K-Style Radius Gutter, .050 Aluminum

$475.00

Our .050 Mill Finish Aluminum K-Style Radius Gutter is available in 5″ and 6″ sizes; 90″ sections only.

2-3 weeks lead time.

One radius angle per template (each change in angle will require a separate template). Radius gutter sections will be manufactured only from Classic Gutter Systems template kit, which will be sent, no charge, upon completion of an estimate.

Protective Crate (necessary for shipping) is $65.00, and up to 5 pieces of radius gutter can be nested in one crate.

Need an estimate? Download, complete and submit our Radius Gutter Estimate Form here.